ClubRalliart.com Your ad here
  #331  
Old 03-01-2015, 08:19 PM
Jackal's Avatar
Jackal Jackal is offline
Senior Member
 
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
Default

So got my parts back from powder coating and started the re assembly process even if some stuff was just temporary just to move the car so more work can be done.

The Valve cover in Candy blue pearl metallic.



The top UR IC pipes

__________________
Instagram #Evosoulralliart 1/4 mile @ 12.7 seconds @ 104 MPH.
Too fricken much to list. Check out my build thread http://clubralliart.com/showthread.php?t=1066
Reply With Quote
  #332  
Old 03-01-2015, 08:22 PM
Jackal's Avatar
Jackal Jackal is offline
Senior Member
 
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
Default

Also took my HKS BOV apart and now have a 1 of a kind 2 tone pc.



__________________
Instagram #Evosoulralliart 1/4 mile @ 12.7 seconds @ 104 MPH.
Too fricken much to list. Check out my build thread http://clubralliart.com/showthread.php?t=1066
Reply With Quote
  #333  
Old 03-01-2015, 08:25 PM
Jackal's Avatar
Jackal Jackal is offline
Senior Member
 
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
Default

AEM Ralliart specific Intake cover



Couple extra pics

__________________
Instagram #Evosoulralliart 1/4 mile @ 12.7 seconds @ 104 MPH.
Too fricken much to list. Check out my build thread http://clubralliart.com/showthread.php?t=1066
Reply With Quote
  #334  
Old 03-01-2015, 08:33 PM
Jackal's Avatar
Jackal Jackal is offline
Senior Member
 
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
Default

Wire tuck with cut splice and extend job.
Starting with re installing the valve cover.



As you can see the harness sitting on valve cover left side is too short to go all the way around the engine and must be cut and then extended.

__________________
Instagram #Evosoulralliart 1/4 mile @ 12.7 seconds @ 104 MPH.
Too fricken much to list. Check out my build thread http://clubralliart.com/showthread.php?t=1066

Last edited by Jackal; 03-16-2015 at 07:21 PM.
Reply With Quote
  #335  
Old 03-01-2015, 08:38 PM
Jackal's Avatar
Jackal Jackal is offline
Senior Member
 
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
Default

Now to take the spliced sensor end and put it back together where it was cut off.




Soldering and heat shrinking completed time for some tape.



Ready to route and connect to sensor

__________________
Instagram #Evosoulralliart 1/4 mile @ 12.7 seconds @ 104 MPH.
Too fricken much to list. Check out my build thread http://clubralliart.com/showthread.php?t=1066

Last edited by Jackal; 03-16-2015 at 07:26 PM.
Reply With Quote
  #336  
Old 03-01-2015, 08:40 PM
Jackal's Avatar
Jackal Jackal is offline
Senior Member
 
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
Default

Time to put stuff back together temporarily to be able to move car,
Step 1 : rebuild HKS BOV





Also installed the IC top pipes and AEM intake cover and snorkel



__________________
Instagram #Evosoulralliart 1/4 mile @ 12.7 seconds @ 104 MPH.
Too fricken much to list. Check out my build thread http://clubralliart.com/showthread.php?t=1066

Last edited by Jackal; 03-16-2015 at 07:29 PM.
Reply With Quote
  #337  
Old 03-01-2015, 08:46 PM
Jackal's Avatar
Jackal Jackal is offline
Senior Member
 
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
Default

Next project will be pulling off front end and installing new ETS Evo X IC with upgraded 3.5 inch core in anodized blue along with new Mishimoto silicone couplers and installing Password JDM carbon fiber spark plug cover.
__________________
Instagram #Evosoulralliart 1/4 mile @ 12.7 seconds @ 104 MPH.
Too fricken much to list. Check out my build thread http://clubralliart.com/showthread.php?t=1066
Reply With Quote
  #338  
Old 03-02-2015, 11:20 AM
iralli_iskustvo's Avatar
iralli_iskustvo iralli_iskustvo is offline
Senior Member
 
Join Date: Jan 2013
Location: Missouri
Posts: 704
Default

Looking good man, loving the powder coated blue valve cover! Engine looking clean!
__________________
RA - Built head - Built SST - ID1000cc - GTX3576R - GSC S2 cams - GSC beehives/Ti retainers - Timing Chain kit - ARP head studs - AMS fuel rail - AMS Widemouth dp - TurboXS exhaust - DrivenFab oil catch can - MAP oil pan - MAP cast manifold - AEM wideband - COBB 3 port EBCS - Tial QRJ - Sakura 3.5 intake - Kozmic Walbro 450 fuel pump - Depo Racing fmic/licp - TS engine/exhaust mounts - Cusco bar - D2 RS coil - Megan Racing control arms/toe - Whiteline sway bars - Brembo 6 piston


Tuned by TJ
Reply With Quote
  #339  
Old 03-06-2015, 04:41 AM
chillwill007 chillwill007 is offline
Member
 
Join Date: Mar 2014
Posts: 46
Default

I think honestly u have by far done the most for ralliarts on here. Your the reason I am continuing my search for a ralliart for myself. U have stuck by ur ralliart for a long time and actually drive the hell out of it. Please keep this thread and ralliart alive
Reply With Quote
  #340  
Old 03-06-2015, 12:04 PM
Jackal's Avatar
Jackal Jackal is offline
Senior Member
 
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
Default

Quote:
Originally Posted by chillwill007 View Post
I think honestly u have by far done the most for ralliarts on here. Your the reason I am continuing my search for a ralliart for myself. U have stuck by ur ralliart for a long time and actually drive the hell out of it. Please keep this thread and ralliart alive
Thank you for the kind words and I promise you I will be continuing to do mods and upgrades for the next 5 years and I even have it all planned out already. LOL!
I simply do what I can as I can afford to. It was actually a couple of my old skool car buds that suggested I find a site for cars like mine and do a build thread back in 2009. It wasn't until the following year did I even join the website.

I do have a fairly large binder with all the research I have done for various projects, most of which still haven't happened yet due to lack of funds. But I have taken pretty much most of the car apart and put back together again on various occasions for one reason or another.

If anyone has any questions about their car or future projects, can they private message me and I will do my best to respond to them.

Thanks
Everyone
__________________
Instagram #Evosoulralliart 1/4 mile @ 12.7 seconds @ 104 MPH.
Too fricken much to list. Check out my build thread http://clubralliart.com/showthread.php?t=1066
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 09:40 PM.




Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright (c) 2011 RnD Media LLC