03-17-2011, 11:51 AM
|
 |
Senior Member
|
|
Join Date: Aug 2010
Location: Barrie, ON, Canada
Posts: 207
|
|
How do you change a DRL bulb?
Is it done from the back by removing the washer fluid filler? From the front removing the lens? My dealer wants 60.00 to do it?
__________________
Paul - Barrie, ON, Canada
2009 RalliArt Rotor Glo Orange
Dark Tint, Aluminum Gas Cap, Borla exhaust
and Hankook Ventus,hiflow cat, intake, Evo IX BOV and tune now at 252whp, 265 lbsft....next up turbo, IC, IC pipes, downpipe!
|
03-17-2011, 02:27 PM
|
 |
Super Moderator
|
|
Join Date: Apr 2009
Location: Mountain Zone Lancer (MTZL)
Posts: 4,060
|
|
From the engine bay.
No you shouldnt have to remove washer bottle.
__________________
|
03-18-2011, 12:31 PM
|
|
Senior Member
|
|
Join Date: Aug 2010
Location: Barrie, ON, Canada
Posts: 207
|
|
man - it looks like i do
__________________
Paul - Barrie, ON, Canada
2009 RalliArt Rotor Glo Orange
Dark Tint, Aluminum Gas Cap, Borla exhaust
and Hankook Ventus,hiflow cat, intake, Evo IX BOV and tune now at 252whp, 265 lbsft....next up turbo, IC, IC pipes, downpipe!
|
03-20-2011, 08:46 AM
|
|
Member
|
|
Join Date: Aug 2010
Posts: 89
|
|
it looks to me like u have projectors so in that case yes u have to remove the socket bolt thats holds the funnel parts on, youll barely have remove and i took me over 30mins to install this bulb since i was only able to turn it with 2 of my weakest fingers. the bulbs are set in very tight and will take alot of patience.
|
03-20-2011, 11:54 AM
|
|
Senior Member
|
|
Join Date: Aug 2010
Location: Barrie, ON, Canada
Posts: 207
|
|
thx - no wonder dealer charges so much...lol
__________________
Paul - Barrie, ON, Canada
2009 RalliArt Rotor Glo Orange
Dark Tint, Aluminum Gas Cap, Borla exhaust
and Hankook Ventus,hiflow cat, intake, Evo IX BOV and tune now at 252whp, 265 lbsft....next up turbo, IC, IC pipes, downpipe!
|
04-24-2012, 06:30 AM
|
 |
Senior Member
|
|
Join Date: Jun 2010
Location: Winnipeg, Manitoba ,Canada
Posts: 1,283
|
|
Went to change the inner day time driving light bulb on the passenger side and I removed the washer fluid filler funnel top piece and found I can get to the twist on socket for the HID and the inner signal bulb but there is no socket for the DRL just a small hole where wiring goes through the plastic housing. also the tiny orange lights on the outer corner of both my driving light assemblys are also burnt out. It seems that I need to pull the entire front end off the car as the top screws are accessable but the bottom screws are at the front and down behind the edge of the bumper cover.
Anybody change these bulbs? if so how and how long?
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 11:58 PM.
|
|
Hybrid Mode