ClubRalliart.com Your ad here
  #1  
Old 03-05-2011, 12:00 AM
BravoZero's Avatar
BravoZero BravoZero is offline
Super Moderator
 
Join Date: Mar 2011
Location: NoVA
Posts: 3,212
Send a message via AIM to BravoZero
Default HOW TO: Relocate AWC button to the dash

I take no credit for this modification as it was done by "tjwphoto" on EvolutionM.net. I brought up the idea but he carried it out. This is a good mod to do if you're annoyed at only having the one button sitting below the shifter out of three possible buttons, and having an extra slot or two open up where the TCS button on the dash is located. You could relocate the AWC button up there and replace the blank buttons with the OEM cubby tray that comes on the standard Lancers to hold a phone or iPod or whatever. This guide is word for word by "tjwphoto".

Part 1 of 3:

Quote:
Originally Posted by tjwphoto View Post
new thread for search purposes

Took me about 2 hours; with instruction maybe less
Tools required. Knife, Phillips screw driver, thin flathead to pry, 10mm socket, cutter

My vocabulary may be incorrect because I have no auto background but deal with it. Also this is how I did it, there maybe be an easier way but also deal with it

First step, pop out that awc box with a knife or something strong and thin and unhook the wire harness, also take out the awc button from the box and save it for the dash location, simple process just look at it





Using a 10mm socket, take out bolts inside the center console so you can remove this later. With a very thin flathead, thinner the better, pry up on the plastic cover for the cupholders area or whatever it is to dismantle the center area. see next step.






Pushing toward the cup holders where my fingers are, then sliding them under allows you to grab and pull upward to unhook some of the plastic clips, work this piece loose and take it out.




Reply With Quote
  #2  
Old 03-05-2011, 12:01 AM
BravoZero's Avatar
BravoZero BravoZero is offline
Super Moderator
 
Join Date: Mar 2011
Location: NoVA
Posts: 3,212
Send a message via AIM to BravoZero
Default

Part 2 of 3:

Quote:
Originally Posted by tjwphoto View Post
Unhook the button that holds the shift cover A, and B take the shift knob off.





Then C. pull up on the shifter area and work with it to loosen it free,






Then you can pull it over and let it hang, I did not unhook any wires, just let it hang there. Remove screws in the photo to remove more plastic on the console






Pull out the whole pastic covering off the center console. This allows you to get your fingers in the tight spots and gives you more space, this step may be avoidable but it worked well for me. this is a repeat photo.




Last edited by BravoZero; 03-05-2011 at 12:03 AM.
Reply With Quote
  #3  
Old 03-05-2011, 12:01 AM
BravoZero's Avatar
BravoZero BravoZero is offline
Super Moderator
 
Join Date: Mar 2011
Location: NoVA
Posts: 3,212
Send a message via AIM to BravoZero
Default

Part 3 of 3:

Quote:
Originally Posted by tjwphoto View Post
Take out screws 1, 2, and 3. Open the fuse box and pull on that piece and work it loose until that piece hangs free from the top but still is connected from the bottom. The knee airbag piece stays where it is, I was cautious around the airbag.






Take out a blank button, I used the one on the right because of; (question for anyone: what is connected to the blank button on the left here in my photo??)






Then you have to free the awc wires from the rest of the wires for the center console, which means for at least the 2011, I had to cut these ziptie wire holders which were a pain because you have to be very careful and they were in difficult spots. There were 3 I think. You will then have to free them of electrical tape and you have to get it free enough to bring the wires over to the left part of the dashboard. Didn’t really take detailed photos here but you can easily figure it out. Bring the wires over and connect that awc button to the dash location. Once you get that far I think you’ll easily manage assembling everything back together






hope that works for everyone.
cheers
Reply With Quote
  #4  
Old 03-05-2011, 03:32 AM
RalliNurse's Avatar
RalliNurse RalliNurse is offline
Senior Member
 
Join Date: Jun 2010
Location: Downey, CA
Posts: 1,367
Default

this is a good find...
Reply With Quote
  #5  
Old 03-05-2011, 03:27 PM
BravoZero's Avatar
BravoZero BravoZero is offline
Super Moderator
 
Join Date: Mar 2011
Location: NoVA
Posts: 3,212
Send a message via AIM to BravoZero
Default

I did this today and was successful, very easy to do just time consuming. I relocated mine to the left of the TCS instead because it's easier to see and get to while driving, and from where I sit I can see both buttons.



Reply With Quote
  #6  
Old 03-05-2011, 11:57 PM
Midlifetoy's Avatar
Midlifetoy Midlifetoy is offline
Senior Member
 
Join Date: Dec 2010
Location: Vacaville, CA
Posts: 119
Default

Good info! I have been thinking about doing this, but I really wanted to move the TCC to the center console. I'm thinking the wires are not long enough, but have yet to look into it.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 06:50 AM.




Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright (c) 2011 RnD Media LLC